Representative image · Sencronom
Vacuum and process consumables · Vacuum Bag Film
Nylon Vacuum Bagging Film
Heat-resistant bagging film for autoclave and oven cures. Folds into complex molds and resists tearing under pressure.
VT-N200
- Operating range
- ≤ 212 °C≤ 414 °F
- Thickness
- 50µm1.97mil
- Elongation at break
- 550%
- Width
- 1520mm59.8in
- Roll length
- 150m492ft
Technical properties
| Parameter | Value | Condition | Test method |
|---|---|---|---|
| Mechanical | |||
| Elongation at break — MD | 550% | direction not stated | ASTM D882 |
| Physical / dimensional | |||
| Thickness | 50µm1.97mil | ||
| Color | Pink | ||
| Chemical / surface | |||
| Resin system compatibility | Epoxy, Polyester, Vinyl ester | ||
| Process / commercial | |||
| Roll width | 1520mm59.8in | ||
| Roll length | 150m492ft | ||
| Process compatibility | Oven cure, Vacuum infusion, Autoclave | ||
| Other | |||
| Tensile strength at break | 95MPa | ASTM D882 | |
Where it sits in the vacuum bag
The vacuum bag from mould to bag, with the layers each method uses. Hover over a layer or pick one from the list.
Method
7Vacuum bagThis productSeals the stack; under vacuum it presses atmospheric pressure onto the part.
Layers, top to bottom
Numbers show the layup order.
Representative layup; layers vary with the method and the part.
Operating range
≤ 212 °C≤ 414 °F
032100212200392300 °C572 °F
- Maximum service temperature
- 212°C414°F
Method suitability
- Oven cureSuitableSuitable for Oven cure
Holds vacuum without softening in heat.
- Vacuum infusionSuitableSuitable for Vacuum infusion
Works, but stiffer than needed at low temperature.
- AutoclaveSuitableSuitable for Autoclave
Resists tearing under pressure.
Supply and storage
- Resin compatibility
- Epoxy
- Polyester
- Vinyl ester
- Packaging
- Roll, 150 mRoll, 492 ft
- Storage
- In its packaging to keep out moisture, in a cool area
Alternatives in this group
Vacuum Bag Film · Differences are relative to this product.
| Compare | Product | T max °C°F | P max barpsi | Elongation at break | Thickness | Tensile strength at break | Oven | Infusion | Autoclave | Product page |
|---|---|---|---|---|---|---|---|---|---|---|
| Co-extruded Vacuum Bagging FilmVT-P120 | 120°C248°F−92−166 | – | 500%−50−50 | 75–80µm2.95–3.15mil | – | Not used with this method | Suitable for Vacuum infusion | Not used with this method | ||
| Self-Releasing Vacuum Bagging FilmVT-K150B | 150°C302°F−62−112 | – | 500%−50−50 | 50µm1.97mil | 50MPa−45−45 | Suitable for Oven cure | Suitable for Vacuum infusion | Suitable for Autoclave | ||
| Co-extruded Vacuum Bagging Film, Epoxy and PhenolicVT-K170 | 170°C338°F−42−76 | – | 400%−150−150 | 50µm1.97mil | 45MPa−50−50 | Suitable for Oven cure | Suitable for Vacuum infusion | Suitable for Autoclave | ||
| Modified Nylon Vacuum Bagging FilmVT-N204B | 204°C399°F−8−14 | 6.9bar100psi | 415%−135−135 | 50µm1.97mil | 96MPa+1+1 | Suitable for Oven cure | Suitable for Vacuum infusion | Suitable for Autoclave | ||
| Nylon Vacuum Bagging Filmthis productVT-N200 | 212°C414°F | – | 550% | 50µm1.97mil | 95MPa | Suitable for Oven cure | Suitable for Vacuum infusion | Suitable for Autoclave | ||
| Silicone Vacuum MembraneVT-S230 | 230°C446°F+18+32 | 7bar102psi | 600%+50+50 | 1.5mm0.059in | – | Suitable for Oven cure | Suitable for Vacuum infusion | Suitable for Autoclave | ||
| Modified Nylon Vacuum Bagging Film, 232 °CVT-N232 | 232°C450°F+20+36 | 6.9bar100psi | 350%−200−200 | 50µm1.97mil | 85MPa−10−10 | Suitable for Oven cure | Suitable for Vacuum infusion | Suitable for Autoclave |